Waterfront Insights
Dock Materials for Salt Water: Wood, Composite, and Aluminum
A dock is several systems at once: pilings in the water, framing above it, decking you walk on, and hardware holding it together. Each faces a different exposure, and the right material for one is not always right for the others.
Think in zones, not one material
The American Wood Protection Association’s use category system, summarized in the USDA Wood Handbook, sorts treated wood by how harsh its exposure is 1. On a dock, that maps cleanly:
- In the water (pilings, bulkhead members, bracing): UC5, for salt or brackish water and the adjacent mud zone. UC5B covers waters from New Jersey to Georgia, which includes North Carolina 1.
- Ground contact and critical structure: UC4B covers critical components with high decay potential, including salt-water splash; UC4C covers critical structural components in severe environments 1.
- Above ground (decking, rails): UC3, exterior wood exposed to the weather but not in ground contact 1.
The North Carolina Coastal Federation’s dock guidance likewise calls for marine-grade materials, including UC5B and UC5C lumber, composite decking, and galvanized fasteners, and warns against cheap or untreated wood near seawater 6.
Pressure-treated wood
Treated southern pine remains the workhorse for pilings and framing. In the water, no wood is immune to marine borers, and no commercially important U.S. wood is resistant enough to use untreated where borers are active 2. High preservative retention and deep penetration are what make marine piling last; spots with shallow or erratic treatment are attacked first 2.
Treated wood also has to be handled correctly. Cuts and bolt holes made after treatment should be field-treated, and pile tops cut after driving should be treated and capped 4. Waterborne preservatives can promote corrosion of metal fasteners, which is one reason hardware choice matters 1.
Not every preservative belongs in salt water. The Wood Handbook notes that high retentions of chromated copper arsenate (CCA), around 2.5 pounds per cubic foot, give good resistance to Limnoria and Teredo, and that dual treatment (a copper-containing waterborne preservative followed by creosote) is possibly the most effective protection against all types of marine borers 1. Pentachlorophenol, by contrast, is ineffective against marine borers and is not recommended for marine piles or timbers in coastal waters 1. For waterborne-treated pine in direct seawater exposure, only sapwood faces should be allowed 1.
Fresh cuts made on site can be partly protected with a thorough application of copper naphthenate, and pile ends cut after driving should get at least two generous coats followed by a protective cover 1. In practice, that means the lumber tag and the crew’s field habits matter as much as the species.
Composite decking
Composite decking keeps wood away from your feet, but it is not a structural replacement for treated pilings and framing. It is also not immune to the environment: in a Forest Products Laboratory study, experimental wood-plastic composites matched to commercial decking showed fungal decay after outdoor exposure in harsh conditions, with a sunny site in Hawaii the most aggressive 5. Practical takeaways are to follow the manufacturer’s span and fastening rules, keep boards draining, and understand the warranty terms that come with the product.
Gapped, flow-through decking that lets water pass during storms and wider board spacing to keep boards from lifting in high water are recommended for coastal docks regardless of decking material 6.
Ironwood and other hardwoods
Dense tropical hardwoods are prized for decking. The Wood Handbook rates ipe heartwood in its "very resistant" category for decay 2. Natural resistance has limits, though: even very decay-resistant species may need preservative treatment for important structural uses, and for severe decay conditions pressure-treated wood is generally recommended over resistant heartwood 2. In the water, only a handful of foreign species, such as greenheart, have shown borer resistance, with uneven results 2.
Aluminum and galvanized framing
Aluminum is common at the waterfront for gangways, platforms, decking, and catwalks, and many alloys offer high corrosion resistance to the marine atmosphere along with a good strength-to-weight ratio 4. The caution: aluminum is subject to pitting and crevice corrosion in marine environments, especially when submerged, and it should not be chosen over steel solely for corrosion resistance 4. Where pitting can be tolerated and crevices are eliminated, aluminum alloys can be used successfully where low weight matters 4.
Mixing metals is the other risk. In salt water, dissimilar metals in contact, such as stainless steel and aluminum, can undergo galvanic corrosion, and the metallic compounds in some wood preservatives can drive the same reaction with connectors 3. FEMA advises keeping fasteners and connectors of similar metals 3. Galvanized steel framing relies on its zinc coating, and FEMA notes that thick hot-dip galvanizing (G185 or higher) and stainless steel improve corrosion protection 3.
Fasteners: the small parts that fail first
- Use hot-dip galvanized or stainless steel connectors and fasteners; Type 304 or 316 stainless exceeds the minimum G185 zinc-coating requirement 3.
- Salt spray is heaviest near breaking waves and declines over the first 300 to 3,000 feet inland, so docks sit in the harshest exposure there is 3.
- Use bolts rather than nails for structural connections 6.
- Inspect connectors at least annually, and replace any that are corroding 3.
We have built with pressure-treated wood, composite decking, ironwood, vinyl, aluminum, and galvanized steel framing. The right mix depends on your budget, the site, and how much upkeep you want. We are glad to walk through the trade-offs for your property.
Frequently Asked Questions
What treatment level should dock pilings have in North Carolina?
Wood in salt or brackish water falls under the UC5 use categories, and UC5B covers waters from New Jersey to Georgia, including North Carolina. Above-water framing and decking have lower exposure categories. Confirm the tag on the lumber matches where it will be used.
Is composite decking better than wood for a dock?
Composite decking reduces splinters and refinishing, but it is not structural and can still be affected by moisture and decay fungi in harsh outdoor conditions. Many docks use composite decking on treated wood pilings and framing.
Does aluminum corrode in salt water?
Aluminum resists marine air well, but it can pit and suffer crevice corrosion in marine environments, especially when submerged, and it corrodes faster when touching dissimilar metals. Good detailing and compatible fasteners matter.
What fasteners should be used on a saltwater dock?
Hot-dip galvanized or stainless steel, with similar metals kept together to avoid galvanic corrosion. Use bolts rather than nails for structural connections, and inspect hardware at least once a year.
Sources
- Wood Handbook, Chapter 15: Wood Preservation (FPL-GTR-190, 2010), USDA Forest Service, Forest Products Laboratory.
- Wood Handbook, Chapter 14: Biodeterioration of Wood (FPL-GTR-282, 2021), USDA Forest Service, Forest Products Laboratory.
- NFIP Technical Bulletin 8: Corrosion Protection for Metal Connectors and Fasteners in Coastal Areas (2019), Federal Emergency Management Agency (FEMA).
- UFM 4-150-07, Waterfront Facilities: Operation and Maintenance (March 2026), U.S. Department of Defense, Unified Facilities Manual (Whole Building Design Guide).
- Field and Laboratory Decay Evaluations of Wood-Plastic Composites (Ibach, Gnatowski & Sun, Forest Products Journal, 2013), USDA Forest Service, Forest Products Laboratory (Treesearch).
- Building Better Docks in Coastal North Carolina (homeowner one-sheet, NOAA Marine Debris Program funded), North Carolina Coastal Federation.
Related services
How we can help
Docks & Piers
Custom docks and piers built for coastal water and the way you use them.
Dock & Pier Repair
Restore aging decking, rails, and pilings before small problems become big ones.
Floating Docks
Stable access that rides changing water levels.
Boat Lifts
Sized to your vessel for easy, protected water access.
Keep reading
More waterfront guides
Dock Piling Repair vs. Replacement: Signs, Options, and What Drives Cost
Pilings carry the whole dock, and most of their damage happens where you cannot easily see it. Here is how to spot trouble, what the repair options are, and what decides between repair and replacement.
Floating vs. Fixed Docks on the North Carolina Coast
With four to five feet of average tide in much of Brunswick County, the choice between a fixed and a floating dock comes down to how you board, what you keep at the dock, and what the site allows.
Bulkheads vs. Seawalls in North Carolina: Rules, Materials, and Alternatives
The terms get used interchangeably, but North Carolina treats a wall on a sound or canal very differently from one on the ocean beach. Here is what the rules allow and how the material and design options compare.
Lets talk
Ready to Improve Your Waterfront?
Tell us what youre planning, where the property is located, and what youd like the waterfront to do for you. Well follow up to talk through options.
